Standard Operating Values
		Trigger Tubes													1.10	1.15	1.20
															high	hihi	maxc
				Home Current (uA)				Home Current (uA)						P1	2424	2535	2645
			HV (V)	no beam	beam		HV (V)	no beam	beam					A1	2210	2310	2411
		Spare	DISABLED			SPARE1	DISABLED							DI	1177	1231	1284
		P1	-1850		2204	P2	-1750		2079					P2	2287	2391	2495
		A1	-1700		2009	A2	-1750		2089					A2	2298	2402	2507
		DI	-1800		1070									VetoN	2724	2847	2971
														VetoS	2917	3050	3182
		Veto Tubes
														D1I	2373	2481	2588
				Home Current (uA)				Home Current (uA)						D2I	2366	2474	2581
			HV (V)	no beam	beam		HV (V)	no beam	beam					A1U	2380	2489	2597
		VetoN	-1800		2476	VetoS	-1800		2652					A1D	2384	2492	2600
														A2U	2362	2469	2576
MAPMT Tubes														A2D	2379	2487	2596
														A1I	2396	2505	2614
		Home Current (uA)		Position (mm)				Home Current (uA)		Position (mm)				A1O	2369	2477	2585
	HV (V)	no beam	beam	nominal	max		HV (V)	no beam	beam	nominal	max			A2I	2402	2512	2621
D1I	-940	2138	2157		33.60	D2I	-940	2131	2151		30.69			A2O	2407	2516	2626
A1U	-940	2135	2164		30.60	A2U	-940	2133	2147		33.35			P1U	2373	2481	2588
A1D	-940	2134	2167		35.11	A2D	-940	2138	2163		35.44			P1D	2372	2479	2587
A1I	-940	2158	2178		18.48	A2I	-940	2152	2184		20.91			P2U	2375	2483	2591
A1O	-940	2142	2154		23.42	A2O	-940	2145	2188		27.98			P2D	2373	2481	2588
P1U	-940	2135	2157		28.08	P2U	-940	2135	2159		30.07			P1I	2408	2517	2627
P1D	-940	2133	2156		25.96	P2D	-940	2133	2157		27.43			P1O	2401	2510	2620
P1I	-940	2171	2189		30.57	P2I	-940	2156	2187		32.52			P2I	2406	2515	2624
P1O	-940	2157	2183		28.41	P2O	-940	2159	2184		33.69			P2O	2402	2512	2621
If a voltage box is green, ramp that voltage. Disabled slots are because there are no tubes attached to that channel.
Values in this table are set as 100% in the HVGui.
If a name is orange, that channel goes to PAUSED state when ramping to 0. Ack the minor error this causes.
If a positon box is green, try to insert that pot. If red, it is disabled.
Currents are for reference and to check if tubes are working properly. Beam values will vary store by store.
Max position is for reference and is the value where halo was effected by 1.25% or rates exceeded 300kHz
Use the provided insertion tables to determine operating positions for pots. It is not uncommon for quadrupole pots to have their
rates double over the home rate. Dipole pots will have end rates as much as 6 times higher. If a pot has rates over 250kHz
at home, it is unlikely that it can be successfully inserted. End points are determined by rates above 250kHz or an
increase in appropriate halo of 20% phalo < 10kHz, 20% ahalo < 6kHz, whichever occurs first. You can exceed the 250kHz if you
are close  to nominal and the rate will not exceed 300kHz by much.
Depending on home rates, try the closest insertion table possible (one with smallest sigma). Look over old elogbook entries
to see where pots have been inserted recently for comparison.
Last Updated 14/February/05